Перейти к содержимому

Not sure which rbAmp you need? Answer four questions or draw your panel

Two lines, several clamp ratings and two clamp types. Start from what you want to see, and you get the parts list.

The choice applies per point, not per house: STD where the number must be right, BASIC on the branches you only want to see. Add later, never replace.

  1. 1What to measure
  2. 2Monitor or account
  3. 3Where the data goes
  4. 4Your installation

Which one do I need?

Pick the task, not the module. We will work out the hardware — the line, the model, the sensor rating and what else you need — from your answers. Three or four questions.

Both lines measure the same things. The difference is what you can do with the numbers: BASIC is for watching a circuit — over months the small errors add up; STD counts energy on the device, in both directions, down to very small loads — for numbers you will rely on. You choose that on the next step; it applies to any task below, including single circuits.

Tick one task or several — most panels end up with a meter on the input and modules on the branches; we build one combined setup.

Nothing selected yet — pick one task, or several.

Skip the wizardContinue → Monitor or account?

How will you use the energy data?

This is the only question that decides the line, and it applies per point — the input, a branch, a tenant feed.

Load control uses live current, no counters needed — any STD you add is for the accounting, not for the control loop.

Ask where the number ends up. If it ends up on a chart — to see when the heat pump runs, whether the workshop is on, how the evening peak looks — watching is enough, and BASIC does it at the lowest cost per circuit.

If it ends up in a report, a comparison with the utility, or a decision about money — how much the solar really gave back, what a tenant owes, whether the new boiler paid off — you want a counter that lives on the device, counts both directions and does not drift with your controller's uptime. That is STD, and it is the same answer for a single branch as for the input.

And if the thing you are hunting is small — standby, chargers, the night baseline — a clamp sized for the whole circuit will show you "something", STD will show you a number.

← Back

Choose one — or pick the mix.

Continue → Where the data goes

Where should the data go?

Who reads the module decides the interface and what else goes in the box. Pick the one you will use first — STD serves a second path later without any change.

← Back

Pick the first consumer of the data.

Continue → Your installation

A few things about your panel

Only what changes the parts list: the sensor rating, the number of modules, whether we add a clamp. Nothing here changes the line you chose.

Supply at the point you meterSupply to each unit

Look at the main breaker: one pole or a wide breaker with three. Most houses are single-phase; workshops, heat pumps and three-phase inverters are often three-phase.

Add a main meter at the input?Optional

Branches tell you where the energy goes; a meter at the input tells you how much comes in — and, with solar, how much goes out. The sum of the branches is never the whole house.

Main breaker rating

Printed on the breaker: C25, C40, C63… This sets the current sensor: it must cover the breaker rating with headroom, and a sensor far above it loses resolution on small loads.

Above 100 A the kit sensors do not cover the input. Meter the branches rather than the input, or contact us.

How many circuits do you want on their own channel?

Count the breakers you want to see separately. You can start with one or two and add modules later — they share the same bus.

Count the loads you want to control or watch live — each needs a current channel. Current-only modules carry 1, 2 or 3 channels.

More than 8 channels: several modules on one bus — the parts list shows how many.

How many separate meters — tenants, rooms, workshops?

One STD meter per unit. Each keeps its own import/export counters and answers on the bus as its own unit.

Add some circuits or appliances to the meter?Optional

A whole-house meter tells you how much. A few branches — the boiler, the heat pump, the workshop, the charger — tell you where. Same bus, read by the same controller.

A whole-house meter tells you how much. A few branches — the boiler, the heat pump, the workshop, the charger — tell you where. On the STD line that is one STD-UI1 per branch, each with its own counters.

Do you already have SCT-013 clamps?

BASIC modules accept the common SCT-013 split-core clamps (the 1 V output type). If you have them, we leave the clamp out and you keep the cost down.

← Back

Answer the questions above.

Show my setup →

Your setup

Start over

The panel builder appears here on the live page.

Prices, stock and exact sensor options are read from the product cards.

BASIC — monitor

Live V · I · P; energy added up on your controller.

Consumption only, lowest cost per circuit.

I-series SCT-I1 / I2 / I3: live current for control.

Interface: I²C. Needs a controller (ESP32, Arduino, Raspberry Pi).

STD — account

Counters on the device, saved every second.

Import and export separately; very small loads resolved.

Interfaces: I²C, or Modbus RTU over UART TTL with an external RS-485 transceiver.

Works standalone as a Modbus meter, or on the same I²C bus as BASIC. Measured characteristics

BASICSTD
RoleMeasureMeasure & Meter
Energy on the deviceno (master computes)yes, counters saved every second
Direction (import/export)consumption onlyyes, two counters
InterfacesI²CI²C, or Modbus RTU (ext. RS-485)
Phases1 per module1 or 3
Sensoryour SCT-013 clampin the kit, calibrated and labelled
Standaloneno (needs a master)yes (Modbus RTU, ext. RS-485)
TrustSCT-013 characteristics per ratingevent log, device certificate, signed records, signed firmware
Buildopenopen, DIN-clip enclosure
Statusavailableavailable

Watching the house

BASIC modules + SCT-013 clamps

Home with solar

STD-UI1 + BASIC branches

Three-phase input

STD-U3I3

Meter for an inverter

STD-UI1 + external RS-485 transceiver

Workshop sub-metering

STD-U3I3: energy counters per channel

Full parts lists with prices for a house, a flat, a workshop or a solar home: Project kits.

If you want Wi-Fi and an app with nothing to assemble, rbAmp is not the right product.